Glock17 produkcija

Taip, vietos tobulejimui visada yra ir bus, bet jei prailgintas detuves ismetejas ir prailgintas spynos fiksatorius bei "minusinis" konektorius palengvina darba su ginklu kvaila butu tuo nepasinaudoti

O galima tiesiog nieko nekeitus saudyti, vietos tobulejimui vaaaaaaaaaaaa tiek, beje pakeitimai ryskaus rezultato neduoda, aktualu tik kai saulys saudo pakankamai aukstame lygyje kad ir 1/100 s. turi itakos

Žodžiu, baikit vaikščioti aplink taisykles, kaip šuo aplink stulpą myžčiodamas.
Rutkis pasakė, kad nieko daryt negalima ir tema baigta Patys išrinkome jį IPSC regiono direktoriumi- čia tas pats kaip apaštalas žemėje.
Jei dar diskusija tęsis tai ir aš tuoj su savo Openu, ateisiu į produkciją ......

Parašė: mygun2big4you, at: 2007-04-13 14:56

Taigi, pavyko prisiskambinti J. Tegge ir issiaiskinau.
Pakomentavo panasiai kaip ir V. Pinto.
V. Pinto, kur pacitavo ramas123, aiskiai pasako kad "option" siulomos detales G yra kaip visu G modeliu detales o ne tik G34 ar ..., todel PD GALIMA!
Valio!
Bet nepamirskit paskaityti idemiai iki galo,
kur pabreziama, kad jei tam tikros dalys yra arba butu siulomos kaip "optons" jos yra specialiai atmestos. Kur yra detuves galima pamatyti kad detuve 33 talpos yra siuloma yr G17 bet tai negalima PD, (net ir Open nes per ilga:woohoo: )
Geru rezultatu!!!
SauliusR.

Sveiki,

tai kaip supratau is paskutinio komentaro, glokui 17 dabar galima deti ir prailgintus detuves ir spynos ismetiklius,ir trauke su - ar + ir taikiklius ir net 122 ilgio vamzdi is 17A ir vis tiek jis bus PD.

???

Sveiki,
manau sis atsakymas viska isaiskina geriausiai (zodziu auksciau nurodytas dalis drasiai galima naudoti):

Vince Pinto
19 Apr 2006, 12:19 am
Post #11


IPSC Secretary

Hi folks,

Let me break the subject rule down for you:

19. Original parts and components offered by the OFM as standard equipment, or as an option, for a specific model handgun on the IPSC approved handgun list are permitted, subject to the following:<snip>

The expression "standard equipment" means "the basic configuration of the handgun". Using a G17 as an example, this means 17 round magazines, fixed front and rear sights made of polymer, the standard (5lb) connector, the standard mag and slide releases, the standard trigger spring, the standard spring cups and the standard 114mm barrel and so on.

The expression "option" means 10, 19, 31 & 33 round mags, adjustable front and rear sights made of polymer or steel (with or without tritium inserts), the minus or plus connectors, the extended mag and slide releases, the NY1 or NY2 trigger springs, the maritime spring cups and the (Australian) "17A" 122mm barrel. Each of these items are approved by Glock for the G17, whether you order them during your original purchase or retrofit them later.

The expression "for a specific model handgun" means that just because a particular part or component will fit your handgun, it's not permitted unless Glock list that item as being an option for your model handgun. For example, let's say that a G34 barrel will work flawlessly in a G17, it's not permitted because Glock don't offer the G34 barrel as an option for the G17 (of course the G34 also exceeds the maximum 127mm allowed in PD, but I'm just trying to illustrate a point here).

The expression "subject to the following" acts as a "clawback", whereby certain items are specifically denied, eventhough they qualify as an "option" (e.g. +2 baseplates and higher capacity mags). Note that lower capacity mags (e.g. 10 round) are acceptable.